• E6000 Premium Glue 4 Pack

    E6000 Premium Clear Industrial Strength Glue – 4 Pack of Small 5.3ml Tubes

    £9.99
    Add to cartLoading Done
  • E6000 Premium Glue 29.5ml

    E6000 Premium Industrial Strength Clear Adhesive Glue 29.5ml

    £9.99
    Add to cartLoading Done
  • e6000 Premium Glue with precision tips

    E6000 Premium Industrial Strength Clear Adhesive Glue 29.5ml with Precision Tips

    £10.99
    Add to cartLoading Done
  • E6000 Premium Glue 59.1ml

    E6000 Premium Industrial Strength Clear Adhesive Glue 59.1ml

    £13.99
    Add to cartLoading Done
  • 144g Famowood

    Famowood Latex Wood Filler Cherry & Dark Mahogany

    £6.99£39.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Famowood Latex Wood Filler Golden Oak | Other colours/shades can be found by clicking here.INSTRUCTIONS FOR SAFE USEFollow these step-by-step directions when using FAMOWOOD Latex Wood Filler:1. For best adhesion, cracks or defects should be clean and dry.2. Press firmly into defect by hand or putty knife.3. A thin film will dry within minutes. Lower temperatures require longer drying periods.4.When dry, sand flush with surrounding surfaces.5. Surfaces may be painted, varnished, lacquered, waxed, or shellacked, after FAMOWOOD application.6. FAMOWOOD can be drilled, nailed, planed, or sawed like ordinary wood.7. Clean tools, while still wet, with water or soap and water. If the product has dried on tools, use chlorinated solvent or steam.8. Close container after each use.

    Famowood Latex Wood Filler Golden Oak

    £6.99£39.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Famowood Latex Wood Filler 576g

    Famowood Latex Wood Filler Maple

    £6.99£9.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Famowood Latex Wood Filler Natural | Other colours/shades can be found by clicking here.INSTRUCTIONS FOR SAFE USEFollow these step-by-step directions when using FAMOWOOD Latex Wood Filler:1. For best adhesion, cracks or defects should be clean and dry.2. Press firmly into defect by hand or putty knife.3. A thin film will dry within minutes. Lower temperatures require longer drying periods.4.When dry, sand flush with surrounding surfaces.5. Surfaces may be painted, varnished, lacquered, waxed, or shellacked, after FAMOWOOD application.6. FAMOWOOD can be drilled, nailed, planed, or sawed like ordinary wood.7. Clean tools, while still wet, with water or soap and water. If the product has dried on tools, use chlorinated solvent or steam.8. Close container after each use.

    Famowood Latex Wood Filler Natural

    £6.99£39.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • 144g Famowood

    Famowood Latex Wood Filler Oak

    £6.99
    Add to cartLoading Done
  • Famowood Latex Wood Filler 576g

    Famowood Latex Wood Filler Red Oak

    £6.99£39.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • 144g Famowood

    Famowood Latex Wood Filler Walnut

    £6.99
    Add to cartLoading Done
  • 144g Famowood

    Famowood Latex Wood Filler White

    £6.99
    Add to cartLoading Done
  • 144g Famowood

    Famowood Latex Wood Filler White Pine

    £6.99
    Add to cartLoading Done
  • Shoe Goo II Glue 26.1ml

    Shoe Goo II (2) UK approved Glue 26.6ml

    £7.99
    Add to cartLoading Done
  • Shoe Goo Shoe Repair Glue 59.1ml

    Shoe Goo II (2) UK approved Shoe Repair Glue 59.1ml

    £9.99
    Add to cartLoading Done
  • E6000 Glue

    E6000 Plus Multi-purpose Glue

    £6.99£8.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • E6000 Glue Trade Pack

    E6000 Glue Trade Pack 6 Tubes For The Price of 5 Multi-purpose Glue 56.1ml

    £44.95
    Add to cartLoading Done
  • E6000 Snip Tips

    Genuine E6000 Plus Nozzle Snip Tips x10

    £1.99
    Add to cartLoading Done
  • Pink Unicorn SPiT - Pixie Punk Pink, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!PINK PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedPink Unicorn SPiT mixes with the Sparkling SPiT rangeMahogany Paint, Gel & Stain < Back | Next > Red Paint, Gel & StainDIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.DIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    Pink Unicorn SPiT – Pixie Punk Pink

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • E6000 Spray Glue

    E6000 Spray Adhesive

    £6.99£8.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Red Unicorn SPiT - Molly Red Pepper, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!RED PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedRed Unicorn SPiT mixes with the Sparkling SPiT range  Pink Paint, Gel & Stain < Back | Next > Orange Paint, Gel & StainDIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.DIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    Red Unicorn SPiT – Molly Red Pepper

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • E6000 Extreme Tack

    E6000 Extreme Tack

    £4.99
    Add to cartLoading Done
  • Orange Unicorn SPiT | Phoenix Fire

    Orange Unicorn SPiT – Phoenix Fire

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • E6000 Fray Lock

    E6000 Fray Lock

    £5.99
    Add to cartLoading Done
  • Yellow Unicorn SPiT | Lemon Kiss

    Yellow Unicorn SPiT – Lemon Kiss

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • E6000 Fabri Fuse

    E6000 Fabri Fuse

    £5.99
    Add to cartLoading Done
  • White Unicorn SPiT - White Ning, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!WHITE PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedWhite Unicorn SPiT mixes with the Sparkling SPiT rangeYellow Paint, Gel & Stain < Back | Next > Cyan Paint, Gel & StainDIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.DIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    White Unicorn SPiT – White Ning

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Cyan Unicorn SPiT - Zia Teal, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!CYAN PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedCyan Unicorn SPiT mixes with the Sparkling SPiT rangeWhite Paint, Gel & Stain < Back | Next > Green Paint, Gel & StainDIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.DIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    Cyan Unicorn SPiT – Zia Teal

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Green Unicorn SPiT - Dragons Belly, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!GREEN PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedGreen Unicorn SPiT mixes with the Sparkling SPiT rangeCyan Paint, Gel & Stain < Back | Next > Blue Paint, Gel & StainDIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.DIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    Green Unicorn SPiT – Dragons Belly

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page
  • Blue Unicorn SPiT - Blue Thunder, allows anyone to turn ordinary objects into personalised MASTERPIECES! Use on wood, glass, metal, fabric, pottery, wicker, concrete and laminate. Ideal for creating new – or – refinishing thousands of projects. Excellent for crafters, hobbyists, DIYers and pros alike!BLUE PAINT, GEL STAIN and GLAZE in One!Make your project as opaque or vibrant as your dreams requireUse as a paint or dilute with water to create a gel, glaze, stain, white wash or antiquing tintPenetrates deep into bare wood grain or glazes over existing finishes, brightening and highlighting painted surfacesProvides a 3-dimensional effectJasmine scentedBlue Unicorn SPiT mixes with the Sparkling SPiT rangeGreen Paint, Gel & Stain < Back | Next > Purple Paint, Gel & StainDIRECTIONS FOR USE AS A STAIN OR DYE:SHAKE BEFORE USING.Dilute Unicorn SPiT up to 50% with water to make stain. Diluting Unicorn SPiT with water allows you to control the opaqueness and absorption into the porous surface. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean and bare sample piece of the same substrate as your project, gradually adding up to 5 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the bare surface once it is completely void of all oil, sealer, dirt, grime, paint, stain, or anything that may inhibit the product from making contacting with the bare porous surface.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.After drying, lightly buff the surface with a fine grade sand paper (120-220 grit) or extra-fine steel wool (following the grain) to remove any excess or clumps.Dust off thoroughly.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product instructions. High Gloss Sealers will help achieve a three dimensional look.TIPS TO CREATE VARIOUS FINISHES: Intermingle chalky paint finishes or metallic spray paint with Unicorn SPiT to achieve unique finishes. Topcoats must be oil-based. Water-based coatings will alter the look of Unicorn SPiT.DIRECTIONS FOR USE AS A LIGHT GLAZE, WHITE WASH OR ANTIQUING AGENT:SHAKE BEFORE USINGDilute Unicorn SPiT up to 30% with water to make a light glaze, white wash or antiquing agent. Diluting Unicorn SPiT with water allows you to control the opaqueness. Add 10 parts Unicorn Spit in a re-sealable container to be diluted with water. Test the dilution on a small, dry, clean sample piece of the same substrate as your project, gradually adding up to 3 parts water until the desired effect is achieved.Apply the diluted Unicorn SPiT to the surface once it is completely void of all oil, dirt, grime, paint, stain, or anything that may inhibit the product from making contact with the surface to antique, age, paint, highlight or lowlight.Continue to add or blend multiple colours to the surface in separate areas creating designs to achieve the desired look.Once dry, use a soft (dry or damp) cloth to polish away Unicorn SPiT until your desired effect has been achieved.Apply to unsealed chalk or mineral style paint to create custom colour highlighting and lowlighting before sealing.Allow to dry. Dry time is approximately 30-60 minutes (depending on material, humidity and temperature) or until a chalky finish appears.Seal with any oil-based coating/sealer. For better protection and a higher gloss, repeat coats of sealer as indicated on the product’s instructions. High Gloss Sealers will help achieve a three dimensional look.CUSTOM COLOURS: Most water-based paints (chalk style or mineral based) can be mixed with Unicorn SPiT to create custom colours.If you have any further questions then visit our Unicorn SPiT FAQ SectionSafety Data Sheet can be download here.

    Blue Unicorn SPiT – Blue Thunder

    £9.99£12.99
    Select optionsLoading Done This product has multiple variants. The options may be chosen on the product page